we are planing to perfect the algorithm with your gateway antenna .
We already have the a sys , but antenna layout of the gateway is big difference in algorithm .
That is the general problem with every sys , but im worry about the difference between other channel . the angle in each channel is so much diff
Yeah i just known the antenna layout , so our dev can change the alogorithm . i see it in your description of product. It may need more time than i thing .
A
我们现在有AOA网关的部署文档,不是拿去做二次开发的。客户如果基于我们AOA网关的硬件,需要自己做定位算法逻辑,我们会准备一个二次开发文档,好了再发给客户看看
Q
I have connected USB Z-Wave dongle to the hub but can't seem to see it in the system
Aeotec Z-Stick Gen5 Plus, Z-wave Plus USB
can't find the dongle ?
please send us the normal boot.img file as well, so we can revert
A
Please try to flash this boot section and try again ;
Just use the android tool to flash it;
Please flash it in this way ,And make sure the hub is in loader mode;
Change the address to 0x0000a000
We've released a latest firmware for HA, you could kindly check about it. http://gofile.me/5spH1/wpFwxjKnb
But as your gateway doesn't have BLE module, you may need to remove the BLE part for zigbee to function well
Q
I want to install HA by my self
So only Debian is ok, then I will install docker + portainer
I am engineer as well, and want to controll the process
HA firmware means it's preinstalled right? If yes - then I dont need it, will do clean install
A
You could download the image in resource center and try again
Q
I have a question regarding the RAM
Now I have 2gb, can you help to extend it? I have raspberry and other devices
So I can replace it
A
for the DSGW-210 the ram is 2GB
We are now develop the dusun PI4, which is similar to the rpi4
which can support RAM : 4GB
Q
also do you have any manual for the device?
manual as such about using the SIM etc
A
There's integration started with dusun for dusun implementation
Dusunbg96 is for LTE
You could install and check
Q
can we control or address these LED's in HA ?
A
Currently there's no UI in HA for controlling the led but we can add this function if there's certain quantity.
Q
Also please note that I'm using the default ZHA integration
Radio path is - > /dev/ttyUSB0
Radio Type -> EZSP = Silicon Labs EmberZNet protocol: Elelabs, HUSBZB-1, Telegesis
The radio will get added successfully like this
first time i was able to add devices , but after sometime the radio will go offline (not loaded message in integration)
but now nothing works
one thing what i notice now is if its a successful integration when i try to add a new device and if i keep the logs open, the logs related to searching should pop up
but here nothing will come
A
After removing the Bluetooth driver the integrations seems to be getting loaded and stable
更新了固件,让客户停掉蓝牙程序
Q
I need a 'How To' guide in loading Debian into this device, can you help me ?
any compatible ones, bullseye/OpenWrt eetc
any Linux OS that goes with RK3328
if i need to completely re-flash it with a new OS how do i proceed
say i have a bullseye image file, how do i proceed with the installation ?
also the drivers
A
What debian image do you imply?
The default one in HA is just debian
For raw debian image, you could refer to the resource center
It's a raw debian image with all drivers
Q
I need to know how we can access the RGB lights on the device. Could you please help me with that ?
Our requirement is that we need to explore the possibilities of accessing those lights from HA for different notifications purposes
A
There's a program with name dsled
You could kindly check about it
Just run the program and check
Q
Can you tell us how to use the WiFi connectivity of this device ?
also about configuring the LTE
A
If should be enabled by default, if not, please check this one
Q
The gateway default WIFI setting is in AP mode.
Can I change it to client mode to connect to my existing WIFI network?
Where to change the setting?
A
Currently the gateway only enables the AP mode by default, if user would like to enable the station mode, please log in the gateway using ssh and with wpa_suppclient to enable it.
Q
Comments
1 comment
你好,試用ZIGBEE2MQTT 連接,連接的位置是 "/dev/ttyUSB0", 回饋如下
1.) 有沒有方法可以 POWER ON/OFF ZIGBEE 的無線模塊, DSM-04B (EFR32MG21)?
2.) 是否需要更新固件?
Please sign in to leave a comment.